- 您现在的位置：买卖IC网 > Sheet目录253 > SS-01GLPT (Omron Electronics Inc-EMC Div)SWITCH LEVER SPDT .1A .110QC
Precautions
■ Correct Use
Mounting
Mount the Switch onto a flat surface. Mounting on an uneven surface
may cause deformation of the Switch, resulting in faulty operation or
breakage in the housing.
Operating Stroke Setting
Take particular care in setting the operating stroke for the pin plunger
models. Make sure that the operating stroke is 60% to 90% of the
rated OT distance. Do not operate the actuator exceeding the OT dis-
tance, otherwise the life expectancy of the Switch may be shortened.
Using Microloads
Using a model for ordinary loads to switch microloads may result in
faulty operation. Instead, use the models that are designed for micro-
loads and that operate in the following range;
■ Cautions
Handling
Turn OFF the power supply before mounting or removing the Switch,
wiring, or performing maintenance or inspection. Failure to do so may
result in electric shock or burning.
Solder Terminal Connection
When soldering lead wires to solder terminals, first insert the lead
wire conductor through the terminal hole and then solder.
Make sure that the temperature at the tip of the soldering iron is
350 to 400 ° C. Do not take more than 3 seconds to solder the switch
terminal, and do not impose external force on the terminal for 1 min
after soldering. Improper soldering involving an excessively high
temperature or excessive soldering time may deteriorate the charac-
teristics of the Switch.
Quick-Connect Terminals
Wire quick-connect terminals (#110) with receptacles. Insert the ter-
30
0.16 mA
26 mA
1 00 mA
minals straight into the receptacles. Do not impose excessive force
on the terminal in the horizontal direction, otherwise the terminal may
be deformed or the housing may be damaged.
24
Use appropriate #110 QC connectors, made by N ippon Tanshi or
12
Operatin g ran g e
for micro load
models SS-01P
Operatin g
ran g e for
g eneral-
load models
SS-3P
Tyco Electronics, to mate with the quick-connect versions of the
switch. These connectors are not sold by OMRO N . Contact N ippon
Tanshi or Tyco Electronics to purchase these connectors.
PCB Terminal Connection
5
Inoperable
ran g e
1 mA
100 mA 16 0 mA
When using automatic soldering baths, we recommend soldering at
260 ± 5 ° C within 5 seconds. Make sure that the liquid surface of the
solder does not flow over the edge of the board.
0
0.1 1 10 100 1,000
Current (mA)
However, even when using microload models within the operating
range shown above, if inrush current or inductive voltage spikes
occur when the contact is opened or closed, it may increase contact
wear and so decrease the service life. Therefore, insert a contact
protection circuit where necessary.
When soldering by hand, as a guideline, solder with a soldering iron
with a tip temperature of 350 to 400 ° C within 3 seconds, and do not
apply any external force for at least 1 minutes after soldering. When
applying solder, keep the solder away from the case of the Switch
and do not allow solder or flux to enter the case.
Insulation Distance
Use a separator between the switch and metal mounting panels, to
ensure proper dielectric characteristics are achieved.
Subminiature Basic Switch
SS-P
107
发布紧急采购，3分钟左右您将得到回复。
相关PDF资料
SS-1-4
SWITCH PIN PLUNGER 0.1A
SS-5GL21D-12
SWITCH BASIC SUBMINI ROLLR LEVER
SS-5GL4025
SWITCH 5A HINGE SOLDER
SSCEA31C
SWITCH LIMIT WHEEL PLUNG SPDT
SSPT7F-7PF20-R
CRYSTAL 32.768KHZ 7PF SMD
ST3215SB32768E0HPWZZ
CRYSTAL 32.768KHZ 9.0PF SMD
ST363016LG
BOX STEEL 41.8X30X16" GREY
ST603616SS
BOX ST STEEL 65.8X36X16" NAT
相关代理商/技术参数
SS01GLT
制造商:Omron Electronic Components LLC 功能描述:HINGE LEVER SPDT 1.8OZ/.1AMP 制造商:Omron Electronic Components LLC 功能描述:Switch Snap Action N.O./N.C. SPDT Hinge Lever Quick Connect 0.1A 125VAC 30VDC 0.49N Screw Mount
SS-01GLT
功能描述:HINGE LEVER SPDT 1.8OZ/.1AMP RoHS:是 类别:开关 >> 快动，限位，拉杆 系列:SS 其它有关文件:Declaration of Conformity 标准包装:1 系列:*
SS-01GL-T
功能描述:基本/快动开关 HINGE ROLLER LEVER
RoHS:否 制造商:Omron Electronics 触点形式:SPDT 执行器:Lever 电流额定值:5 A 电压额定值 AC:250 V 电压额定值 DC:30 V 功率额定值: 工作力:120 g IP 等级:IP 67 NEMA 额定值: 端接类型:Wire 安装:Panel
SS01GP
制造商:Omron Electronic Components LLC 功能描述:SWIT SA NO/NC SPDT PIN PLUNGER SLDR 0.1A 125VAC 30VDC 1.5N T - Trays 制造商:Omron Electronic Components LLC 功能描述:SWITCH BASIC SPDT .1A SLDR
SS-01GP
功能描述:基本/快动开关 0.1A Pin plunger Solder terminals
RoHS:否 制造商:Omron Electronics 触点形式:SPDT 执行器:Lever 电流额定值:5 A 电压额定值 AC:250 V 电压额定值 DC:30 V 功率额定值: 工作力:120 g IP 等级:IP 67 NEMA 额定值: 端接类型:Wire 安装:Panel
SS01GPB
制造商:Omron Electronic Components LLC 功能描述:SWITCH,SUBMINIATURE,SNAP ACTION,PIN PLUNGER,PCB TERMINALS EVEN PITCH,0.1A 制造商:Omron Electronic Components LLC 功能描述:SWIT SA NO/NC SPDT PIN PLUNGER PC PINS 0.1A 125VAC 30VDC 1.5 - Trays 制造商:Omron Electronic Components LLC 功能描述:SWITCH BASIC SPDT .1A PCB
SS-01GPB
功能描述:基本/快动开关 0.1A Pin plunger PCB terminals even
RoHS:否 制造商:Omron Electronics 触点形式:SPDT 执行器:Lever 电流额定值:5 A 电压额定值 AC:250 V 电压额定值 DC:30 V 功率额定值: 工作力:120 g IP 等级:IP 67 NEMA 额定值: 端接类型:Wire 安装:Panel
SS01GPD
制造商:Omron Electronic Components LLC 功能描述:SWIT SA NO/NC SPDT PIN PLUNGER PC PINS 0.1A 125VAC 30VDC 1.5 - Trays 制造商:Omron Electronic Components LLC 功能描述:SWITCH BASIC SPDT .1A PCB